Inexpensive investment to prolong life of rotary motors - ferrite donuts, beads

[Alie K]

Ferrite donuts can prolong the life of your motor. I was told that when I purchased my Blitz rotary. I'll try to take a picture of my setup at the studio so you don't have to look at my painful computer drawing of a ferrite donut with a power cord threaded through it for very long...

74

[RobJobe]

Also insure that you always use the same polarity. Color code your clipcord and always connect the same way. Rca isn't an issue obviously.

[Alie K]

Yes! Forgot to mention that. I took a red and black sharpie marker and colored the metal ends on my contact points.

[Alie K]

Here's a great site explaining ferrite donuts and beads - and there's pictures!

http://www.gbrcaa.org/ntoa/Filters,%20Chokes%20and%20OIs.htm

[rjdadio]

132131We offered these all the way back in 2005. 130 This ferrite is a snap over that cable type. The best is to loop it once, like the second picture shows. The third picture is the EMI filter open. You have most likely seen them on other equipment in the past. The object of the ferrite is to filter out electrical noise. - Ray

[rjdadio]

I should have added....that it depends on the power supply you are using. Most modern power supplies have outputs that are smooth so as not to be a problem running a rotary machine. Personally, I don't see the need for the ferrite if you use a quality power supply. Here in the states you could to find the clamp on ferrite at RadioShack for under $10 or find them online thru electronic suppliers. If you buy online, know that there are different grades of ferrites that filter at different frequencies. You need ones that will filter thru the lower frequency spectrum. Some new rotary machines may use brushless motors and these would be more sensitive to electrical noise than a brush type, but again....use a good power supply.

What is most important is the polarity that you run your machine. As Alie stated before it is a good idea to mark your clip cord connections for polarity. Colored heatshrink works good too. Slip it over the contact wire away from the connection point and then heat....voila!

You would think that after how many years there would be a standard direction on a clip cord.....but still not really. Back when I was doing coil "relay" machines for a company, I suggested using bipolar "non polarized" caps in the machines because they were having caps blow out for some reason....I wonder why??? Because they were hooked up bass-ackwards....DUH!
When working on the wireless footswitch adapter...again years ago....I was amazed to find that MOST of the tattoo supply (big ones too) companies at the time did not know the polarity of their units!... I called each one and asked. So make sure to run you machines with the proper polarity that the machine manufacture recommends.....it will live longer. Use a voltmeter and check.....

[Alie K]

Wow, that's really interesting, Ray! Kind of funny about the distributors knowing about their power supplies though. I guess I might not know much about my power supply if it were made in China! lol (Though, that doesn't go for everyone...

[AllisonLawson]

Where can I get one of these donut things?

[The Limey]

If Ray doesn't have them Radio Shack should.

[Administrator]

Where can I get one of these donut things?

Active Surplus in Toronto.

[AllisonLawson]

Thanks guys. I figure it wont hurt to use one. :)

[rjdadio]

I think I still have a couple in stock......should I offer these critters again?

[The Limey]

I don't see why not Ray

[Administrator]

Feel free to make a post in the Buy and Sell if you don't want to put them up on the website right away.

[caglakhan]

would the new critical power supply put out smooth enough current to eliminate any need for one of these?

[Administrator]

Not really required but It was suggested by a builder some time ago as a just in case to help keep the current clean going to your machine.

[Alie K]

Not really required but It was suggested by a builder some time ago as a just in case to help keep the current clean going to your machine.

...and to help preserve the life of the motor.

[turnrock]

i have a few of those ferrite beads i salvaged from random old computer wires and broken electronics but i cant figure out how to tell the difference between them.they seem to almost never have any markings.anyone know a way to figure out the specs? im probably better off just buying a new one, there cheap enough.

[Inkslinger]

Ray I would buy several if you're gonna sell em.
Russ

[John]

SurplusGizmos.com also has ferrites I'm not sure if they have them online but I live close to the retail store and I think they only cost $1-$2. I picked a few up a while ago from them, they also had a bunch of sizes.