Search:

Type: Posts; User: Magnu

Page 1 of 15 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: pencil again

    by Magnu
    Replies
    8
    Views
    17,515

    Nice one Casey

    Nice one Casey
  2. Thread: Gyro pilot

    by Magnu
    Replies
    3
    Views
    10,987

    Sorry for the late reply folks It's done in...

    Sorry for the late reply folks
    It's done in pencil with a lot of 6B on bristol board paper
  3. Thread: Gyro pilot

    by Magnu
    Replies
    3
    Views
    10,987

    Gyro pilot

    27381
  4. Replies
    6
    Views
    8,794

    Ah my mistake I thought you had an original round...

    Ah my mistake I thought you had an original round piston converted to the square
    I too found the orignal to be a bit noisy but by fine tuning IE lots of trial and error adjusting the cam on the...
  5. Replies
    6
    Views
    8,794

    Nice pieces Casey Did you find the square piston...

    Nice pieces Casey
    Did you find the square piston made a difference to the machine? I have an orginal Ali and it's one of my daily drivers although more for packing and blending than shading for...
  6. Thread: Hi all

    by Magnu
    Replies
    15
    Views
    18,557

    Welcome to the forum Mog glad you find it helpfull

    Welcome to the forum Mog glad you find it helpfull
  7. Replies
    2
    Views
    4,660

    If it's the Bizarre and not the Hyper (2 differnt...

    If it's the Bizarre and not the Hyper (2 differnt machines) Bizarre uses an eccentric cam and the Hyper is a swash type The stroke length on the Bizarre is changed by changing the cam, the machine...
  8. Replies
    90
    Views
    62,774

    Me too please Dale

    Me too please Dale
  9. Thread: Before and After

    by Magnu
    Replies
    21
    Views
    17,101

    That's one hell of a turd polish

    That's one hell of a turd polish
  10. Hello and welcome to the forum Once bitten...

    Hello and welcome to the forum Once bitten forever smitten
  11. Replies
    17
    Views
    12,391

    Hello and welcome to the forum and your new...

    Hello and welcome to the forum and your new addiction
  12. Thread: Hi

    by Magnu
    Replies
    8
    Views
    13,179

    Hello ansd welcome to the forum

    Hello ansd welcome to the forum
  13. Thread: New Rotary

    by Magnu
    Replies
    16
    Views
    12,050

    One of my Hyper V2s has been used almost...

    One of my Hyper V2s has been used almost exclsively for about 6 months now and has never let me down.
  14. Replies
    8
    Views
    6,631

    Hello and welcome to the forum

    Hello and welcome to the forum
  15. Replies
    5
    Views
    6,270

    Hello and welcome to the forum

    Hello and welcome to the forum
  16. Replies
    8
    Views
    7,090

    Hello ans welcome to the forum

    Hello ans welcome to the forum
  17. Thread: Hey everyone

    by Magnu
    Replies
    4
    Views
    5,795

    Hello and welcome to the forum

    Hello and welcome to the forum
  18. Thread: Hyper V3 setup?

    by Magnu
    Replies
    10
    Views
    12,552

    Have you applied any lubrication to the slide? As...

    Have you applied any lubrication to the slide? As this will cause a lot of noise if it is run dry you could also try tightening up the adjuster screws either side of the slide to cut out excessive...
  19. Replies
    5
    Views
    5,113

    Hello and welcome to the forum

    Hello and welcome to the forum
  20. Replies
    10
    Views
    10,759

    Hello and welcome to the forum

    Hello and welcome to the forum
  21. Just used mine to line and fill some tribal and...

    Just used mine to line and fill some tribal and have decided to make it my go to machine for filling blackwork, with a 9 textured mag it flew in, very impressed.
  22. Many congats on a well deserved award Alie, that...

    Many congats on a well deserved award Alie, that is a cracking piece
  23. Speaking from the other side of the needle the...

    Speaking from the other side of the needle the Blitz feels exactly like a coil and unlike any other rotary I've experienced and it has done a great job packing and blending with a 21 ooo mag.
  24. Replies
    11
    Views
    9,788

    Hello and welcome to the forum

    Hello and welcome to the forum
  25. Replies
    6
    Views
    5,478

    Hello and welcome to the forum

    Hello and welcome to the forum
Results 1 to 25 of 366
Page 1 of 15 1 2 3 4