Results 1 to 9 of 9

Thread: Impact rotary

  1. 01-11-2015, 02:13 PM #1
    Mission Tattoo
    Mission Tattoo is offline
    Senior Member
    Join Date
    Dec 2011
    Location
    Santa Barbara CA
    Posts
    353
    Post Thanks / Like

    Impact rotary

    Does any one know how to take this machine apart? I need to clean and lube it as well as replace the spring any help would be great
    Reply With Quote Reply With Quote
  2. 01-11-2015, 04:54 PM #2
    Mission Tattoo
    Mission Tattoo is offline
    Senior Member
    Join Date
    Dec 2011
    Location
    Santa Barbara CA
    Posts
    353
    Post Thanks / Like
    Anyone?
    Reply With Quote Reply With Quote
  3. 01-11-2015, 04:59 PM #3
    nivek
    nivek is offline
    Knows Whats Up!
    Join Date
    Aug 2010
    Location
    Kitchener
    Posts
    2,048
    Post Thanks / Like
    Im not going to get political - but given their design i would suggest looking at the bishop maintenance video on youtube. I suspect it will be very similar
    Sidewinders, MC2, Mc 14, MC13, Halo, Lollis, Specific, Diablo. Tried many more
    Reply With Quote Reply With Quote
  4. 01-11-2015, 09:13 PM #4
    Mission Tattoo
    Mission Tattoo is offline
    Senior Member
    Join Date
    Dec 2011
    Location
    Santa Barbara CA
    Posts
    353
    Post Thanks / Like
    There are no scews holding the motor like the bishop and no clamp
    Reply With Quote Reply With Quote
  5. 01-11-2015, 10:32 PM #5
    Ofeloner
    Ofeloner is offline
    Senior Member
    Join Date
    Jan 2014
    Location
    Idaho
    Posts
    495
    Post Thanks / Like
    What ever you do, don't send it in to them to have it fixed up,, I made that miatake and I never was mailed my machine back, The dude who makes those machines is a drug addict.
    Reply With Quote Reply With Quote
  6. Post Thanks / Like
    Like tatu richie liked this post.
  7. 01-12-2015, 12:15 AM #6
    slicksteel
    slicksteel is offline
    Machine Builder I build Tattoo Machines slicksteel's Avatar
    Join Date
    Dec 2010
    Location
    San Jose & Morgan Hill,CA
    Posts
    4,133
    Post Thanks / Like
    The machine uses two setscrews that go thru the front of the frame which is under the slider.The maxon motors has two set screw threads on the front of it. The front is nylon so be very careful not to strip them by getting the screws back in at a angle.
    You must align the slide to each set screw and unscrew thru the sliders hollow needle pin area.
    You can plug in the machine and use a few volts to turn over the motor while holding the slide down to line it up to each screw.



    SSI -SUPER SLICK IRONS-top shelf custom coil machines
    American Made Machines

    [email protected]
    https://www.facebook.com/evanstattooing
    Reply With Quote Reply With Quote
  8. 01-12-2015, 09:38 PM #7
    Mission Tattoo
    Mission Tattoo is offline
    Senior Member
    Join Date
    Dec 2011
    Location
    Santa Barbara CA
    Posts
    353
    Post Thanks / Like
    Awsome thank you tricky little bugger
    Reply With Quote Reply With Quote
  9. 01-15-2015, 01:38 AM #8
    Noa
    Noa is offline
    Member
    Join Date
    Nov 2012
    Location
    St.Albans Vermont
    Posts
    82
    Post Thanks / Like
    Does anyone know if the

    Wrath Cartridge Grip (1'') Model B (Ttech)



    will fit the Impact rotary?




    Reply With Quote Reply With Quote
  10. 01-15-2015, 01:04 PM #9
    Mission Tattoo
    Mission Tattoo is offline
    Senior Member
    Join Date
    Dec 2011
    Location
    Santa Barbara CA
    Posts
    353
    Post Thanks / Like
    Not sure but it fits the rpg and kingpin cart grips
    Reply With Quote Reply With Quote
« Flite question. | Using an RCA clip cord on a cheyenne Hawk? »

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules