Results 1 to 7 of 7
  1. 01-19-2012, 11:14 PM #1
    G.Graves
    G.Graves is offline
    Senior Member G.Graves's Avatar
    Join Date
    Apr 2011
    Location
    Bremerton, wa.
    Posts
    295
    Post Thanks / Like

    direct drive rotory works, WH irons

    Alot of people that have the dd RW, have been bumbed it is to long. It is possible to fix this, i have done my machine and my buddy's.
    after doing this, it fits the tubes perfect. rotory 2.jpgrotory.jpg





    Then i changed up the WH irons alittle, I had two and sold one. I like the way these machines looked allot! I was hoping for it to perform better, and was about to sell it but then wanted to try to change it up a bit. Very happy with the way it runs and I will post up videos of it running before and after.

    rotory 4.jpgrotory 1.jpg
    Last edited by G.Graves; 01-20-2012 at 01:30 AM.
    Reply With Quote Reply With Quote
  2. 01-20-2012, 05:10 AM #2
    OwlsDen
    OwlsDen is offline
    Knows Whats Up! OwlsDen's Avatar
    Join Date
    May 2011
    Location
    Nürnberg
    Posts
    3,647
    Post Thanks / Like
    Very cool, I may have to cut my dd RW down too. How much did you chop off?
    Reply With Quote Reply With Quote
  3. 01-20-2012, 01:00 PM #3
    G.Graves
    G.Graves is offline
    Senior Member G.Graves's Avatar
    Join Date
    Apr 2011
    Location
    Bremerton, wa.
    Posts
    295
    Post Thanks / Like
    I took off about an inch, I will check it to be exact. Then I smoothed out the edges so it feels better on the hand I the cut groves into them so it hold with out the little pin.
    Reply With Quote Reply With Quote
  4. 01-20-2012, 03:47 PM #4
    gangstajay
    gangstajay is offline
    Knows Whats Up! gangstajay's Avatar
    Join Date
    Nov 2010
    Location
    Tampa
    Posts
    2,341
    Post Thanks / Like
    i like the mod to the work horse.
    VAGABOND JAY
    Reply With Quote Reply With Quote
  5. 01-20-2012, 07:29 PM #5
    G.Graves
    G.Graves is offline
    Senior Member G.Graves's Avatar
    Join Date
    Apr 2011
    Location
    Bremerton, wa.
    Posts
    295
    Post Thanks / Like
    Quote Originally Posted by gangstajay View Post
    i like the mod to the work horse.
    Thanks, it is very quiet now and consistent. I have another idea for it, but as it is right now I could put it back to the way it was if I wanted.
    Reply With Quote Reply With Quote
  6. 01-23-2012, 05:16 PM #6
    MedusaTattoo
    MedusaTattoo is offline
    Senior Member MedusaTattoo's Avatar
    Join Date
    Nov 2011
    Location
    Chicago and Greece
    Posts
    307
    Post Thanks / Like
    i just got a WH and the noise is one negative i will try also to make some changes, i will post them when is ready
    Reply With Quote Reply With Quote
  7. 01-23-2012, 05:47 PM #7
    linsner666
    linsner666 is offline
    Member linsner666's Avatar
    Join Date
    May 2011
    Location
    Hohenpolding / bavaria
    Posts
    34
    Post Thanks / Like
    Send a message via AIM to linsner666 Send a message via Skype™ to linsner666
    here u go .... http://www.rotarytattoo.com/showthre...s-Rotary/page5
    Reply With Quote Reply With Quote
« Aaron Cain "5" | Very much appreciate NeoTat advice »

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules