Page 1 of 2 12 LastLast
Results 1 to 10 of 20
  1. #1
    Knows Whats Up!
    Join Date
    Jul 2011
    Location
    Vancouver bc
    Posts
    1,049
    Post Thanks / Like

    Bishop rotary info

    mine arrived yesterday , came with 3 little samples of super lube, and says inside the box: for instructions on lubrication and to order more, visit the website. no where on the site could i find where to order more of the super lube , and no instruction page on how to use it on the machine... or how much? do I use one entire small tueb that came on the machine? seems like a lot... not sure how i would get it all in there. if you could give me some info franco it would be great , used the bishop with a 9 semi tight liner last night and put them in smooooth as butta cant wait to get another

    I did find this info on voltages on there new site that is being built maybe helpfull to some as i was running it pretty low before i found this.

    USING A ROTARY

    By adjusting the voltage of the Bishop, you can achieve the right speed to enable the best results for:

    • Solid & creamy color
    • The softest black & grey work
    • Solid black lining work


    • Being that the rotary machines differ from coil machines there is an obvious shift that must occur in the transition from heavy coils to “The Bishop” to be assured that you will be one of the many that have crossed over, you must do many tattoos with the Bishop Rotary and follow our voltage guidelines.
    • BUILT IN “GIVE ” SPRING.
      By adjusting the speed of the machine through the volts you can make the machine hit harder or softer and the benefit is that you can adjust the give by your hand speed, hand stroke and hand pressure and of course the voltage. THIS IS THE MOSE ACCURATE AND ORGANIC WAY TO HAVE “GIVE”
    • FOR SOLID COLOR:
      use between 8.5-9.5 volts (note: glance between these volts and find the speed that most works with your unique hand speed and once you discover the right connection, you will be a customer for life).
    • FOR BLACK AND GREY WORK:
      use between 9.5-10 volts (note: due to the very consistent hit of this machine, the lightest greys are pushed deeps into the epidermis of the skin ensuring that when the tattoo heals, you wont lose that light grey that is often hard to keep).
    • FOR PRECISION LINING:
      use between 10.5-11 volts (note: you must stretch skin a little more than normal to ensure proper line work and you will see how solid and consistent the Bishop puts lines in).
    Last edited by joelhague; 11-23-2011 at 04:47 PM.

  2. #2
    Knows Whats Up!
    Join Date
    Jul 2011
    Location
    Vancouver bc
    Posts
    1,049
    Post Thanks / Like
    another important tip i learned off the site is use a rubber nipple not paper towel or hard plastic , to allow for a bit of "self give" that way you can get used to one feeling and stick with it

  3. #3
    Member JayFatInk's Avatar
    Join Date
    Oct 2011
    Location
    Centralia
    Posts
    42
    Post Thanks / Like
    Good stuff...I love my bishop..
    If your dumb,you better be tough or better yet bullet proof...!!

  4. #4
    Knows Whats Up! gangstajay's Avatar
    Join Date
    Nov 2010
    Location
    Tampa
    Posts
    2,341
    Post Thanks / Like
    cool shit
    VAGABOND JAY

  5. #5
    Site Technical Admin The Sheriff Administrator's Avatar
    Join Date
    Aug 2010
    Location
    Toronto
    Posts
    3,282
    Post Thanks / Like
    Quote Originally Posted by joelhague View Post
    another important tip i learned off the site is use a rubber nipple not paper towel or hard plastic , to allow for a bit of "self give" that way you can get used to one feeling and stick with it
    Since you are in Vancouver you might want to check out goodguy supply for the by the foot silicone tubing. Its really soft!

  6. #6
    Knows Whats Up!
    Join Date
    Jul 2011
    Location
    Vancouver bc
    Posts
    1,049
    Post Thanks / Like
    ok so this is my first machine with a needle clip instead of bands, i guess you HAVE to bend your needlebars eh? i never did before as my artist doesnt do it ... but today i was like wtf is up with my machine and it was my mag floppin around in the tube the clip doesnt really hold it secure without this bend? correct me if im doing something wrong? didnt notice it at first as i was using a round tube that kept the liner pretty snug


    and hey ya thanks for the tip i will check out the tubing i saw that in another post somewhere

  7. #7
    Site Technical Admin The Sheriff Administrator's Avatar
    Join Date
    Aug 2010
    Location
    Toronto
    Posts
    3,282
    Post Thanks / Like
    If you are in the US check Lucky Supply but good guy is not far from you. You can probably find the same stuff at a hobby store (I thinks its a 5mm OD/2mm ID) as well but if you just wanna take the tubing for a test drive its good to order some from one of these suppliers as it would be turn key and its cheap as chips.

  8. #8
    Knows Whats Up!
    Join Date
    Jul 2011
    Location
    Vancouver bc
    Posts
    1,049
    Post Thanks / Like
    sweet ill order some of that up, .... anyone know about my prevoius question,... does bishop / neo tat require a bend in the needlebar to keep the needle in the back of the tube , i think i already know the answer is yes i just want to confirm this with others who use the bishop

  9. #9
    Administrator/The Site Owner The Sheriff Alie K's Avatar
    Join Date
    Aug 2010
    Location
    Toronto, Canada
    Posts
    2,054
    Post Thanks / Like
    Quote Originally Posted by joelhague View Post
    ok so this is my first machine with a needle clip instead of bands, i guess you HAVE to bend your needlebars eh? i never did before as my artist doesnt do it ... but today i was like wtf is up with my machine and it was my mag floppin around in the tube the clip doesnt really hold it secure without this bend? correct me if im doing something wrong? didnt notice it at first as i was using a round tube that kept the liner pretty snug


    and hey ya thanks for the tip i will check out the tubing i saw that in another post somewhere
    First, make sure your needle wasn't in there upside down by accident. Sometimes I do that, and my needle flops around. You shouldn't need to bend the needle like you would with a coil machine. If you bend it at all, just a very slight bend closer to the needles than in the middle should work.

    Sometimes the types of disposable tubes you use can also have an effect. I find that with some of them, I have to put my needles in upside-down (with the bar on the bottom) and use a slight bend the opposite way I usually do it. Otherwise, the needles sit funny towards the top of the tube.
    Not too bad for a GIRL, eh?

  10. #10
    Senior Member turnrock's Avatar
    Join Date
    Jul 2011
    Location
    Boston
    Posts
    290
    Post Thanks / Like
    Quote Originally Posted by Administrator View Post
    If you are in the US check Lucky Supply but good guy is not far from you. You can probably find the same stuff at a hobby store (I thinks its a 5mm OD/2mm ID) as well but if you just wanna take the tubing for a test drive its good to order some from one of these suppliers as it would be turn key and its cheap as chips.
    word on the street is luckysupply gets their “rc fuel line" made to their specs from the manufacturer and the stuff you get at a hobby shop could be harder or softer

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •