Page 1 of 7 123 ... LastLast
Results 1 to 10 of 61
  1. #1
    Machine Builder I build Tattoo Machines fkirons's Avatar
    Join Date
    Dec 2010
    Location
    Miami Beach, Florida
    Posts
    2,143
    Post Thanks / Like

    Spektra "Vorteks" in the works

    I wanted to keep this one secret until the machine was released but since the actual final product will changed a lot from this early rendering I wanted to share this to give you an idea of a new product we'll be launching some time next year. It uses the same MotorBolt System as the Halo.
    This project was supposed to lunch in parallel with the Halo but the Halo itself was a lot more work than we expected. Therefore we decided to wait and do this right.

    The latest design is much more streamline and it has a give system. It's not a swash, it doesn't have an angle plate neither.
    The system that propels the a bar is pretty cool and unique.
    The machine will be clavable and have similar features as the Spektra plus new stuff we are bringing to the table.

    We are in the prototyping stage and testing the a new give mechanism we designed (one of them).
    Vorteks is the name of this baby.

    We are far from completion and this machine will not be released prior 100s of hours of hardcore testing.
    Last edited by Administrator; 09-18-2012 at 01:01 AM. Reason: Images removed at the request of the original poster. If you want to see them you will have to ask him.
    For Customer service please contact Kayleigh
    Email under "Contact Us" at fkirons.com


  2. Like PAWNJOB, otto, Brian Russell, tatu richie, asA liked this post.
  3. #2
    Knows Whats Up! Zapp's Avatar
    Join Date
    Jan 2011
    Location
    Germany
    Posts
    1,361
    Post Thanks / Like
    I can not believe so far what this machine will do better then the Spektra :-)

  4. #3
    Machine Builder I build Tattoo Machines slicksteel's Avatar
    Join Date
    Dec 2010
    Location
    San Jose & Morgan Hill,CA
    Posts
    4,133
    Post Thanks / Like
    It would be cool if you came up with a small compact light well made angled rca cord to go with these-as all the ones out there now are junk.
    And maybe make this a no spring give one with preset damping built in the abar shaft area that would be in soft med hard models.so you just pick up and go . could say for instance swap the bolt to between a soft an hard setup on the fly.
    Last edited by slicksteel; 09-07-2012 at 09:31 PM.



    SSI -SUPER SLICK IRONS-top shelf custom coil machines
    American Made Machines

    [email protected]
    https://www.facebook.com/evanstattooing

  5. Like Eturnus liked this post.
  6. #4
    Machine Builder I build Tattoo Machines peezie's Avatar
    Join Date
    Aug 2011
    Location
    san jose
    Posts
    242
    Post Thanks / Like
    Those renderings look bad ass. Can't wait to see what this turns into.

  7. #5
    Knows Whats Up! Sage Oz's Avatar
    Join Date
    Oct 2011
    Location
    Bellevue, Washington.
    Posts
    2,724
    Post Thanks / Like
    Wow this is almost exactly what I've been trying to design for the last year, I was preparing to send you a proposal to see what you thought and if you'd be willing to manufacture it but looks like you already have it started lol. Is the drive system using repulsing magnets? Also it'd be cool if there was a hinged or sliding cover that could seal off the front of the machine to eliminate bags

  8. #6
    Senior Member
    Join Date
    Dec 2011
    Location
    Goa
    Posts
    234
    Post Thanks / Like
    Vorteks on the way...

  9. #7
    Senior Member Eturnus's Avatar
    Join Date
    Jul 2012
    Location
    Carteret
    Posts
    439
    Post Thanks / Like
    I saw this when you first put it up. But you had deleted it right away.. Didnt even have the chamce to mastubate to the pic...

  10. #8
    Knows Whats Up! serial1313's Avatar
    Join Date
    Jun 2012
    Location
    Birmingham, Al.
    Posts
    2,272
    Post Thanks / Like
    I appreciate that you are keeping the same motorbolt.

  11. #9
    Machine Builder I build Tattoo Machines fkirons's Avatar
    Join Date
    Dec 2010
    Location
    Miami Beach, Florida
    Posts
    2,143
    Post Thanks / Like
    Quote Originally Posted by Eturnus View Post
    I saw this when you first put it up. But you had deleted it right away.. Didnt even have the chamce to mastubate to the pic...
    ROFFFFLLLLLLLLLLL!!!!hahahahaha
    For Customer service please contact Kayleigh
    Email under "Contact Us" at fkirons.com


  12. #10
    Machine Builder I build Tattoo Machines fkirons's Avatar
    Join Date
    Dec 2010
    Location
    Miami Beach, Florida
    Posts
    2,143
    Post Thanks / Like
    Back to the topic. We are working on several chassis. Trying to stick to the cylindrical slider in a smaller version. The one you see here has a flat slider but we have some cool new stuff that we are testing out.
    For Customer service please contact Kayleigh
    Email under "Contact Us" at fkirons.com


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •